View Profile: MassiveOverkill - Yamaha Wolverine Forum

Yesterday, 01:51 PM

MassiveOverkill replied to a thread The MassiveOverkill method of bleeding your cooling system in X2/X4 How To

Sorry didn't see this Steeper the better but 30-45 degrees would be plenty sufficient with front end up If you don't have an incline, jacking...

6 replies | 220 view(s)

Yesterday, 06:44 AM

MassiveOverkill replied to a thread Using Low Gear - 2019 X2 in Wolverine X2/X4 General Discussion

With over 7K miles on my X4 I use low gear more often just because I want to extend the life of my wet clutch as much as possible with this much...

4 replies | 125 view(s)

08-18-2019, 06:41 AM

MassiveOverkill replied to a thread Only 20hrs in and something squeaking once the X4 is hot. in Wolverine X2/X4 General Discussion

Stock is 205, with Weller ECU flash it's 195 F and stays on down to 185 F.

10 replies | 220 view(s)

08-16-2019, 09:45 AM

MassiveOverkill started a thread Suspension components for the Wolverine X2/X4 forumdisplay.php?f=26&s=a01aa623706aa8e85ea5388d5360a0e2 in [ARG:7 UNDEFINED]

Guys, it's been 2 years now. It's time for front AND rear suspension arms, axles, extended axles, etc. for the X2/X4. The X2/X4 is a Teryx killer...

2 replies | 88 view(s)

08-14-2019, 03:42 PM

MassiveOverkill replied to a thread Yamaha Wolverine X2/X4 mods, tips, and tricks in Wolverine X2/X4 General Discussion

Works great! Throttle modulation is much easier. I still want to pair it up with Throttle Max \ DIY Throttle Max at some point.

144 replies | 67747 view(s)

08-09-2019, 09:56 AM

MassiveOverkill replied to a thread Those of you with Terrabites in Wheels & Tires

It really depends on your terrain and use. I run 18 PSI because I do 50% highway driving. If I rarely drove on the road I'd probably lower pressure...

6 replies | 238 view(s)

08-09-2019, 09:55 AM

MassiveOverkill replied to a thread Major air Lost on rear tire. in Wheels & Tires

I've been eyeing Tusk bead locks as they have much beefier bolts to secure the bead lock ring. You wouldn't have to granny tighten in 20 million...

18 replies | 331 view(s)

08-08-2019, 07:46 PM

MassiveOverkill replied to a thread 2018 X4 Transmission Oil change Question in X2/X4 How To

If you've done the front and rear diff, all that's left for gearboxes is the transmission fluid, the one where the dipstick is under the passenger...

9 replies | 193 view(s)

08-08-2019, 07:35 PM

MassiveOverkill replied to a thread 2020 Wolverine Changes? in Wolverine X2/X4 General Discussion

I've been asked to moderate this post because of the offensive nature of one post, which I'll say, at best, was in poor taste. The OP was able to...

37 replies | 6870 view(s)

08-08-2019, 01:19 PM

MassiveOverkill replied to a thread 2018 X4 Transmission Oil change Question in X2/X4 How To

Transmission is easy. Fill is a dipstick under the passenger seat bottom under a rubber flap and it has a drain plug underneath. Rear diff you'll...

9 replies | 193 view(s)

08-08-2019, 07:34 AM

MassiveOverkill replied to a thread Major air Lost on rear tire. in Wheels & Tires

I'll probably need to buy another set of Terrabites soon and will inspect to see if the Airsoft BB's I'm using for balancing are breaking down and...

18 replies | 331 view(s)

08-08-2019, 07:17 AM

MassiveOverkill replied to a thread Major air Lost on rear tire. in Wheels & Tires

I use my highly-calibrated, built-in torque wrench that God provided me with ;). It's a tedious process basically snugging each bolt in a star...

18 replies | 331 view(s)

08-08-2019, 06:30 AM

MassiveOverkill replied to a thread Major air Lost on rear tire. in Wheels & Tires

You need to re torque your bead lock ring bolts regularly as they will loosen. When initially installing the tires you have to remove the rubber...

18 replies | 331 view(s)

08-07-2019, 04:33 PM

MassiveOverkill replied to a thread Yamaha Wolverine X2/X4 mods, tips, and tricks in Wolverine X2/X4 General Discussion

Another milestone update

144 replies | 67747 view(s)

08-06-2019, 06:56 AM

MassiveOverkill replied to a thread Firewall Guards in Wolverine General Discussion

There was a guy who made them for the Rhino and I actually bought a set. I wish he would get with the times and realize 3 models have since been...

20 replies | 633 view(s)

08-06-2019, 05:56 AM

MassiveOverkill replied to a thread Door removal in Wolverine X2/X4 General Discussion

I hate net-style doors as they're much harder to secure. Weller ECU flash with a machined sheave is your best bet for increased speed unless you...

3 replies | 238 view(s)

08-04-2019, 04:12 PM

MassiveOverkill replied to a thread Wolverine X2/X4 engine codes in X2/X4 Engine

It's in the shop manual.

2 replies | 214 view(s)

08-04-2019, 12:07 PM

MassiveOverkill started a thread Wolverine X2/X4 engine codes forumdisplay.php?f=266&s=a01aa623706aa8e85ea5388d5360a0e2 in [ARG:7 UNDEFINED]

FYI, infocenter will display a code when you have a check engine light. I was expecting the code to flash on and off but it doesn't, it just sits...

2 replies | 214 view(s)

08-04-2019, 12:02 PM

MassiveOverkill replied to a thread The answer to all motor oil questions! in Wolverine General Discussion

Both CD and SG specifications have been obsolete for some time now. I think the Yamaha manuals are suffering from a little bit of 'copy and paste'...

20 replies | 734 view(s)

08-03-2019, 11:48 AM

MassiveOverkill replied to a thread Installing an oil catch can for the X2/X4 in X2/X4 Engine

Only 150 miles but I figured I'd see if it's collecting anything:

5 replies | 414 view(s)

08-01-2019, 07:28 AM

MassiveOverkill replied to a thread Hot Feet in X2/X4 How To

Look closely, battery on the left, ECU on the right ;)

13 replies | 293 view(s)

08-01-2019, 07:12 AM

MassiveOverkill replied to a thread Hot Feet in X2/X4 How To

I just had some flexible black plastic, shoved it in there nonchalantly and threw some insulation behind it for support\extra air-blocking. I...

13 replies | 293 view(s)

08-01-2019, 06:00 AM

MassiveOverkill replied to a thread Installing an oil catch can for the X2/X4 in X2/X4 Engine

Look at the video for the updated mounting location. I doubt the loop will prevent the tank from breathing. If pressures were that low, we wouldn't...

5 replies | 414 view(s)

07-31-2019, 06:05 PM

MassiveOverkill replied to a thread Hot Feet in X2/X4 How To

After doing all my mods, including the latest, which is blocking off the center tunnel. The only heat I experience now is coming out of the parking...

13 replies | 293 view(s)

07-31-2019, 02:44 PM

MassiveOverkill replied to a thread X4 oil puddling in intake ducting issue in Wolverine X2/X4 General Discussion

Forgot to link this solution: https://www.wolverineforums.com/forum/266-x2-x4-engine/27874-installing-oil-catch-can-x2-x4.html

36 replies | 6583 view(s)

07-31-2019, 07:12 AM

MassiveOverkill replied to a thread Hot Feet in X2/X4 How To

Consider the heat coming directly off the radiator and where it's going.

13 replies | 293 view(s)