Are your front Factory Roof Brackets Installed Incorrectly ? - Page 5
Close
Login to Your Account
Yamaha Wolverine Forum

Are your front Factory Roof Brackets Installed Incorrectly ?

This is a discussion on Are your front Factory Roof Brackets Installed Incorrectly ? within the Wolverine X2/X4 General Discussion forums, part of the Yamaha Wolverine X2 & X4 847cc SxS category; Just checked my Service Manual. Page 4-9 & 4-10. It shows channel legs up and installing the bolts from above....

Page 5 of 5 FirstFirst ... 3 4 5
Results 41 to 42 of 42
Like Tree19Likes

Thread: Are your front Factory Roof Brackets Installed Incorrectly ?

  1. #41
    Paper Boy SKELLEY521's Avatar
    Member #
    15792
    Join Date
    May 2019
    Location
    West Virginia
    Posts
    19
    Member #
    15792
    Liked
    10 times
    Just checked my Service Manual. Page 4-9 & 4-10. It shows channel legs up and installing the bolts from above.
    Piston Yamaha likes this.

  2. #42
    Slow Poke Stroodle's Avatar
    Member #
    221
    Join Date
    May 2015
    Location
    Pemberton, BC
    Posts
    37
    Member #
    221
    Liked
    42 times
    I had my factory roof installed with channels down (n). I broke my roof off and just had to replace it. I also swapped my roof cross bars on the cage because the bolts for these brackets pulled out of the tubes. When I put it back together I found the brackets didn't line up like before. I found myself looking to turn them the other way but then I see that the crossbars, which are held in with 2 bolts a side, can rotate a few degrees because these 4 bolt holes are obviously slightly bigger than the bolts and have some wiggle room. Adjusting the "roll" of the crossbar fixed up my issue. Perhaps this is why we are getting different results with people. Also, the front and back cross bar are both drilled and tapped for these brackets, but mine 'seemed' to be slightly different which adds to the difference I came across. Hope this makes sense to all and hopefully this helps with some installs.
    2019 Wolverine X2 SE
    Yamaha Warn 3500 Provantage w/synthetic
    rope and wireless remote
    22" curved LED bar
    Stroodle Aluminum box rails
    Kolpin Stronghold rifle and chainsaw boot
    26" Maxxis BigHorn 3.0
    Hunterworks Sheave/weights
    Weller Racing flash
    On my second roof - don't ask!
    More to come...

Page 5 of 5 FirstFirst ... 3 4 5

Sponsored Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Snorkel your atv Installed
    By tinbasher in forum Gear & Accessories
    Replies: 3
    Last Post: 09-16-2019, 09:01 PM
  2. FS Factory front Aluminum Rim for Sale
    By gip in forum Wolverine Parts
    Replies: 2
    Last Post: 06-11-2018, 02:40 PM
  3. Loctite your roof
    By D1rtsqu1rrel in forum Wolverine General Discussion
    Replies: 8
    Last Post: 11-30-2017, 06:08 AM
  4. Factory roof for rain protection
    By gip in forum Wolverine General Discussion
    Replies: 10
    Last Post: 08-19-2016, 06:30 AM
WolverineForums.com is an independent Yamaha enthusiast website. Content on WolverineForums.com is generated by its users and WolverineForums.com is not in any way affiliated with Yamaha Motor Corporation, U.S.A.